[MAN] networkctl

Content-type: text/html; charset=UTF-8

NETWORKCTL

Section: networkctl (1)
Updated:
Index Return to Main Contents

---

 

NAME

networkctl - Query the status of network links  

SYNOPSIS

networkctl [OPTIONS...] COMMAND [LINK...]

 

DESCRIPTION

networkctl

may be used to introspect the state of the network links as seen by systemd-networkd. Please refer to systemd-networkd.service(8) for an introduction to the basic concepts, functionality, and configuration syntax.  

OPTIONS

The following options are understood:

-a --all

Show all links with status.

-h, --help

Print a short help text and exit.

--version

Print a short version string and exit.

--no-legend

Do not print the legend, i.e. column headers and the footer with hints.

--no-pager

Do not pipe output into a pager.

 

COMMANDS

The following commands are understood:

list [LINK...]

Show a list of existing links and their status. If no further arguments are specified shows all links, otherwise just the specified links. Produces output similar to:

IDX LINK         TYPE     OPERATIONAL SETUP
  1 lo           loopback carrier     unmanaged
  2 eth0         ether    routable    configured
  3 virbr0       ether    no-carrier  unmanaged
  4 virbr0-nic   ether    off         unmanaged

4 links listed.

status [LINK...]

Show information about the specified links: type, state, kernel module driver, hardware and IP address, configured DNS servers, etc.

When no links are specified, an overall network status is shown. Also see the option --all.

Produces output similar to:

●      State: routable
     Address: 10.193.76.5 on eth0
              192.168.122.1 on virbr0
              169.254.190.105 on eth0
              fe80::5054:aa:bbbb:cccc on eth0
     Gateway: 10.193.11.1 (CISCO SYSTEMS, INC.) on eth0
         DNS: 8.8.8.8
              8.8.4.4

lldp [LINK...]

Show discovered LLDP (Link Layer Discovery Protocol) neighbors. If one or more link names are specified only neighbors on those interfaces are shown. Otherwise shows discovered neighbors on all interfaces. Note that for this feature to work, LLDP= must be turned on on the specific interface, see systemd.network(5) for details.

Produces output similar to:

LINK             CHASSIS ID        SYSTEM NAME      CAPS        PORT ID           PORT DESCRIPTION
enp0s25          00:e0:4c:00:00:00 GS1900           ..b........ 2                 Port #2

Capability Flags:
o - Other; p - Repeater;  b - Bridge; w - WLAN Access Point; r - Router;
t - Telephone; d - DOCSIS cable device; a - Station; c - Customer VLAN;
s - Service VLAN, m - Two-port MAC Relay (TPMR)

1 neighbors listed.

label

Show numerical address labels that can be used for address selection. This is the same information that ip-addrlabel(8) shows. See m[blue]RFC 3484m[][1] for a discussion of address labels.

Produces output similar to:

Prefix/Prefixlen                          Label
        ::/0                                  1
    fc00::/7                                  5
    fec0::/10                                11
    2002::/16                                 2
    3ffe::/16                                12
 2001:10::/28                                 7
    2001::/32                                 6
::ffff:0.0.0.0/96                             4
        ::/96                                 3
       ::1/128                                0

 

EXIT STATUS

On success, 0 is returned, a non-zero failure code otherwise.  

SEE ALSO

systemd-networkd.service(8), systemd.network(5), systemd.netdev(5), ip(8)  

NOTES

1.

RFC 3484

https://tools.ietf.org/html/rfc3484

---

 

Index

NAME

SYNOPSIS

DESCRIPTION

OPTIONS

COMMANDS

EXIT STATUS

SEE ALSO

NOTES

---

This document was created by man2html, using the manual pages.
Time: 04:45:33 GMT, September 16, 2022