Header Ads Widget

[MAN] tc-police

Content-type: text/html; charset=UTF-8 Man page of Policing action in tc

Policing action in tc

Section: Linux (8)
Updated: 20 Jan 2015
Index Return to Main Contents

 

NAME

police - policing action  

SYNOPSIS


tc ... action police rate RATE burst BYTES[/BYTES] [ mtu BYTES[/BYTES] ] [ peakrate RATE ] [ overhead BYTES ] [ linklayer TYPE ] [ CONTROL ]


tc ... filter ... [ estimator SAMPLE AVERAGE ] action police avrate RATE [ CONTROL ]


CONTROL := conform-exceed EXCEEDACT[/NOTEXCEEDACT


EXCEEDACT/NOTEXCEEDACT := { pipe | ok | reclassify | drop | continue | goto chain CHAIN_INDEX }  

DESCRIPTION

The police action allows to limit bandwidth of traffic matched by the filter it is attached to. Basically there are two different algorithms available to measure the packet rate: The first one uses an internal dual token bucket and is configured using the rate, burst, mtu, peakrate, overhead and linklayer parameters. The second one uses an in-kernel sampling mechanism. It can be fine-tuned using the estimator filter parameter.  

OPTIONS

rate RATE
The maximum traffic rate of packets passing this action. Those exceeding it will be treated as defined by the conform-exceed option.
burst BYTES[/BYTES]
Set the maximum allowed burst in bytes, optionally followed by a slash ('/') sign and cell size which must be a power of 2.
mtu BYTES[/BYTES]
This is the maximum packet size handled by the policer (larger ones will be handled like they exceeded the configured rate). Setting this value correctly will improve the scheduler's precision. Value formatting is identical to burst above. Defaults to unlimited.
peakrate RATE
Set the maximum bucket depletion rate, exceeding rate.
avrate RATE
Make use of an in-kernel bandwidth rate estimator and match the given RATE against it.
overhead BYTES
Account for protocol overhead of encapsulating output devices when computing rate and peakrate.
linklayer TYPE
Specify the link layer type. TYPE may be one of ethernet (the default), atm or adsl (which are synonyms). It is used to align the precomputed rate tables to ATM cell sizes, for ethernet no action is taken.
estimator SAMPLE AVERAGE
Fine-tune the in-kernel packet rate estimator. SAMPLE and AVERAGE are time values and control the frequency in which samples are taken and over what timespan an average is built.
conform-exceed EXCEEDACT[/NOTEXCEEDACT]
Define how to handle packets which exceed or conform the configured bandwidth limit. Possible values are:
continue
Don't do anything, just continue with the next action in line.
drop
Drop the packet immediately.
shot
This is a synonym to drop.
ok
Accept the packet. This is the default for conforming packets.
pass
This is a synonym to ok.
reclassify
Treat the packet as non-matching to the filter this action is attached to and continue with the next filter in line (if any). This is the default for exceeding packets.
pipe
Pass the packet to the next action in line.
 

EXAMPLES

A typical application of the police action is to enforce ingress traffic rate by dropping exceeding packets. Although better done on the sender's side, especially in scenarios with lack of peer control (e.g. with dial-up providers) this is often the best one can do in order to keep latencies low under high load. The following establishes input bandwidth policing to 1mbit/s using the ingress qdisc and u32 filter:

# tc qdisc add dev eth0 handle ffff: ingress # tc filter add dev eth0 parent ffff: u32 \         match u32 0 0 \
        police rate 1mbit burst 100k

As an action can not live on it's own, there always has to be a filter involved as link between qdisc and action. The example above uses u32 for that, which is configured to effectively match any packet (passing it to the police action thereby).

 

SEE ALSO

tc(8)


 

Index

NAME
SYNOPSIS
DESCRIPTION
OPTIONS
EXAMPLES
SEE ALSO

This document was created by man2html, using the manual pages.
Time: 04:45:58 GMT, September 16, 2022

댓글 쓰기

0 댓글